Make any 1/64 scale wheels fit any 1/64 scale car easily with custom adjustable axles!

If the stock axles are too short or long, you'll need custom axles like these!

Simply bend the axle pin tips a tiny bit with pliers and insert into tubes.

The friction from the bend will hold the pin in place, no need for glue.

Glue is permanent, bending isn't.

If the axle pin is too hard to push in, you've bent it too much so just unbend it a bit.

If the axle pin is sliding out on its own, you need to bend it some more.

SIZE Recomendations:

All sizes work on Hot Wheels, Matchbox, and possibly other 1/64 scale diecast brands. Only the length changes.

The size you need varies alot on the wheels (deep dish vs regular), base of car (this varies), and fitment desired (regular vs tucked vs past fender)

-Short: Kool Kombi, Tooned Cars, Very Deep Dish wheels, wheels tucked in behind fenders like on lowriders/slammed cars/trucks.

--Medium: Normal Wheels on most cars or Slight Deep Dish.

---Long: Widebody cars with non deep dish wheels, Offroad trucks with non deep dish wheels or wide stance (tires sticking out alot past fenders)

Long is the safest bet as you can always trim with dremel disc is needed, but i recommend having all sizes in your toolbox to make things easier/faster :)

--->Buy Individual Axle Sets: CLICK HERE

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------

HOW TO INSTALL:

Drill method:

1) Drill out base rivets with roughly a 9/64" drill bit.

2) Take car apart.

3) Pry open / remove base tabs holding in original wheel axles.

---for plastic bases, you can easily pry them open with small flathead screwdriver, or just snap them off with blade/wire cutters.

---for metal bases, you may be able to snap them off with wire cutters (careful as this will send the tab flying across the room!) if you cannot remove the tab entirely, you will need to use dremel disc to grind off the rest of tab.

---if you don't care about the stock wheels/axles, you can also just bend them out to easily cut the axle with wire cutters

4) Replace wheels/axles

---if the custom wheels don't fit because axle is too short/long, you will need to adjust custom axle sets, see below.

5) Reassemble car.

---If you didn't overdrill, the base might just snap back together, otherwise you will need to lay car on it's roof and add some super glue onto the posts where the rivets used to be, or use some epoxy putty.

Optional: Lower car's ride height by sanding down the interior that holds the axles.

No Drill method:

1) Cut stock axles with wire cutter.

---you may need to bend the axles down to have room to cut them

2) Use custom axles:

---1. Bend axle pins about 10-15 Degrees with pliers

---2. Insert bent pin into axle tube (if it won't go in, you've bent it too much, unbend a bit and try again, if it slides out too easily, bend it more)

---3. Insert 1 wheel into axle tube

---4. Feed axle tube with wheel through car's base

---5. Insert another wheel into axle tube on the other side of car/axle

---6. Insert bent axle pin into axle tube to lock in the wheels

3) Adjust as needed.

---if axle tube is too long: uninstall axle and trim with dremel disc and try again

---if axle tube is too short (rare): pull out axle pins slightly

---if there is play in the wheels, add spacers to fill in the gaps from wheel to base (you can make your own or use my 3D printed spacers for an easier time)

Note: if you don't use drill to open car, you can't lower the car's ride height.

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SHIPPING INFO: for wheels and decals

Flat rate shipping: Doesn't matter how much you buy, same shipping price!

USA: $4.99 (automatically free on orders over $49)

Canada: $9.99 ($5 automatic discount on orders over $49)

International: $12.99 ($5 automatic discount on orders over $49)

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Follow me on Social Media for updates on Restocks and New Releases!

Any questions, feel free to ask :)